Process and Quality Control of Oil Cylinder for 5TG-FC Series (202mm Bore) Front Top dump Truck
Release time:
2026-09-29
Once parameters are confirmed, customers’ top concerns are: What will you do after order placement? How is quality guaranteed? This article introduces the main production processes and control nodes of this 5-stage hinge-mounted front-top hydraulic cylinder, ranging from raw material incoming inspection to finished product delivery.
Raw Material Control
The cylinder tubes adopt standard seamless steel pipes, and piston rods are made of high-quality quenched and tempered steel to guarantee substrate strength and wear resistance. All blanks will undergo material re-inspection and internal defect flaw detection after incoming, eliminating hidden material risks at the source.
Key point: This model features a bore of 202 mm, a stroke of 6500 mm and 5-stage telescopic structure. As a large-bore ultra-long-stroke product, it has extremely strict requirements on raw material straightness, wall thickness uniformity and internal quality, so strict controls are implemented during material selection.
Key Machining Processes
- Cylinder tube inner wall machining: Special equipment is applied for precision machining of each stage cylinder tube to ensure inner wall smoothness and dimensional accuracy, providing a sound working surface for seals.
- Piston rod machining: Each rod goes through rough turning, finish turning, grinding and other multi-step processes to meet standards of cylindricity and surface finish. Straightness control is the priority for ultra-long rods.
- Machining of each stage sleeve: This 5-stage telescopic product requires precise control of fitting clearance between sleeves to achieve smooth telescoping and reliable sealing. More stages bring higher difficulty in controlling accumulated tolerances.
- Hinge pin machining: Two hinge pin sizes (60 mm and 65 mm) are available with precision machining to guarantee fitting accuracy with frame hinge bushings.
- Protective sleeve machining: The 273 mm diameter protective sleeve must meet roundness and straightness requirements to deliver effective protection for internal multi-stage cylinder tubes.
- Welding process: Standard welding procedures are adopted for critical welds on cylinder bottom, oil ports and hinge bases. Penetrant testing and flaw detection are performed to rule out welding defects.
Surface Treatment (Key for Anti-Corrosion & Wear Resistance)
Hard chrome plating is applied on the surface of all piston rods to achieve excellent wear resistance and rust resistance, adapting to outdoor working conditions. Anti-rust primer plus topcoat are sprayed on outer cylinder walls and protective sleeves to improve the overall corrosion resistance of the cylinder.
Note: Ultra-long-stroke hydraulic cylinders have a large exposed area of piston rods, so coating quality is critical. We follow formal standards to prevent coating peeling during long-term operation.
Assembly Process
- All components are thoroughly cleaned before assembly to avoid iron filings, dust and other impurities entering the cylinder interior.
- Special tools are used for seal installation to prevent scratches or distortion and guarantee sealing performance.
- Threaded connections are tightened per standard torque to avoid loosening or over-tightening.
Special attention: The 5-stage cylinder has numerous sealing positions. Each seal must be checked and marked one by one after installation. During assembly of ultra-long-stroke cylinders, rod straightness must be monitored to avoid seal damage caused by forced installation.
Factory Inspection Items
Every hydraulic cylinder must pass the following tests before delivery:
- Pressure resistance test: Hold pressure at a test pressure higher than rated pressure to verify the strength of each stage cylinder and welds.
- Leakage test: Check internal and external leakage of each stage separately to ensure no leakage at all sealing points.
- Operation test: Run full-stroke telescoping under simulated working conditions, inspect smooth movement, abnormal noise or jamming, with special focus on stable transition between stages and stability under full extension for ultra-long-stroke cylinders.
- Synchronization inspection: Verify the extension sequence and speed of each stage comply with design specifications.
- Visual inspection: Confirm intact surface coating, clear marking and installation dimensions consistent with drawings.
Conclusion
From raw materials to finished goods, every 5TG-FC series front-top hydraulic cylinder is manufactured with standardized workflows and multiple inspections. Large bore, ultra-long stroke and 5-stage telescoping impose high requirements on manufacturing precision and process control. We are equipped with proper equipment and inspection methods to guarantee quality. Feel free to contact us if you need specific process documents or test reports.
FAQ
What raw material inspection is carried out for the 5TG-FC 5-stage hydraulic cylinder?
All incoming blanks undergo material re-inspection and internal defect flaw detection. We strictly check straightness, wall thickness uniformity and internal quality of seamless steel tube and quenched tempered steel for this large bore ultra-long stroke cylinder.
What factory tests will be performed on the 5TG-FC cylinder before shipment?
Each cylinder passes pressure resistance test, leakage test, full-stroke operation test, synchronization check and visual inspection to verify strength, sealing performance, smooth telescoping and dimensional compliance.
Why is hard chrome plating critical for ultra-long stroke multi-stage hydraulic cylinders?
Ultra-long stroke piston rods have large exposed working area. Hard chrome plating delivers outstanding wear and corrosion resistance, preventing coating peeling and extending service life under outdoor heavy-duty working environments.