Energy mining equipment oil cylinder | In sales | Process inspection and quality control
Release time:
2026-07-22
Key Quality Control Nodes in the Production Process of Wantong Hydraulic
Wantong Hydraulic has built a complete digital whole-process quality management system to implement targeted closed-loop control for key production procedures, effectively preventing unqualified products from flowing into the next process and ensuring standardized production quality.
The core key quality control nodes cover the entire production and assembly process of hydraulic cylinders, including dimensional sampling inspection of cylinder boring and rolling processing, precision inspection of thread processing, weld quality inspection, assembly inspection of sealing systems, and final assembly pressure test. Each node can only be released automatically by the system after passing the inspection.
In addition to fixed inspection nodes, the company regularly carries out process discipline inspections, conducts accurate quality hazard investigation through production data traceability, and implements targeted correction and preventive measures to realize continuous optimization and full-life-cycle quality control of hydraulic cylinder products.
Handling Standards for Unqualified Products Found in Process Inspection
The company implements the rigid management principle of no circulation of unqualified products, and all quality abnormalities are managed in accordance with the closed-loop process of identification, isolation, evaluation and disposal to standardize abnormal handling and eliminate quality risks.
The causes of all unqualified products are recorded in the system, with reverse traceability to the upstream processing procedures to locate the root cause of defects. Repairable unqualified products will be re-inspected after process adjustment and repair; products that still fail the re-inspection will be forcibly scrapped to avoid defective products entering the finished product link.
Once batch unqualified problems occur in the production process, the production line will be immediately stopped for rectification, and production can only be resumed after the rectification effect is verified to be qualified. Supported by a strict red and early warning mechanism, the company realizes zero outflow of quality problems.
Process Quality Control Methods for Key Components Such as Cylinder Barrels and Piston Rods
For core components including cylinder barrels and piston rods that determine the core performance of hydraulic cylinders, Wantong Hydraulic adopts a dual-inspection system of operator self-inspection + professional patrol inspection to fully guarantee processing accuracy and consistency.
During the processing process, operators conduct self-inspection and record data strictly in accordance with the frequency specified by the process card. Professional inspectors carry out roaming sampling inspection based on professional inspection guidelines, and implement 100% full inspection for key dimensional data to eliminate dimensional deviations.
All inspection data is recorded in the process inspection card and bound with the unique product serial number, realizing the traceability mode of one product with one card and full-process record. Meanwhile, through on-site patrol inspection and data trend analysis, abnormal processing trends can be detected in a timely manner, with dynamic adjustment of process parameters to ensure consistent processing quality of batch products.
Operation Specifications of Trial Run Inspection in Production Process
Trial run is a mandatory pre-delivery inspection item for hydraulic cylinders, which simulates real working conditions to verify the operational reliability of products, with standardized and unified operation procedures.
Before the trial run, completely remove residual air inside the hydraulic cylinder and the system, and thoroughly wipe off oil stains, impurities and foreign matters on the surface of the piston rod and cylinder body to ensure a clean test environment and avoid test result errors caused by foreign matters.
Under no-load working conditions, drive the hydraulic cylinder to complete reciprocating full-stroke operation no less than 5 times. Inspectors focus on observing the stability of the whole operation process and check for abnormal impact noises and jamming phenomena. Only products that pass the trial run inspection can enter the subsequent performance assessment links including pressure resistance test and leakage test.
Inspection Methods for Key Matching Dimensions of Cylinder Barrels and Piston Rods
To ensure the precise matching performance of cylinder barrels and piston rods, Wantong Hydraulic adopts high-precision digital testing equipment and professional testing technologies for multi-dimensional accurate detection of key matching dimensions.
Special measuring tools or coordinate measuring machines are used for multi-point accurate detection of cylinder inner diameter accuracy. Laser scanning technology is applied to realize non-contact full-stroke measurement of piston rod straightness, which effectively improves detection accuracy and coverage. The coaxiality deviation is confirmed through comprehensive error analysis of the mounting reference surfaces of the cylinder body and piston rod.
All detection data is uploaded to the ERP system in real time and archived in binding with the unique product serial number. The system will automatically give an early warning once the dimensional data exceeds the standard, ensuring that all matching accuracies fully meet the design standards and assembly requirements.
Customer On-Site Witness Mechanism for Process Inspection
Wantong Hydraulic supports full transparent quality inspection services and allows customers to send professional technical personnel to the factory for on-site witnessing and supervision of key process inspections.
The on-site witnessing scope includes checking the factory's self-inspection records of each process, verifying the metering certificates and calibration validity of testing equipment, and confirming that the on-site inspection methods and standards are consistent with contract terms and technical agreements.
It is recommended that customers clarify the process witness clauses in the business negotiation stage. The company will coordinate the production schedule in advance, fully open the workshop production site, and cooperate with customers to complete on-site quality acceptance and witness work.
FAQ 1: What core quality control measures are adopted for hydraulic cylinder key components?
Key components such as cylinder barrels and piston rods implement a dual inspection system of operator self-inspection and professional patrol inspection, with 100% full inspection for key dimensions. All inspection data is bound with product serial numbers to realize full-process traceability.
FAQ 2: How does Wantong Hydraulic deal with unqualified products during production?
Unqualified products are strictly isolated and evaluated. Repairable products are reworked and re-inspected, while unrepairable ones are scrapped. Batch quality problems will trigger immediate production line stop rectification to prevent defective products from flowing out.
FAQ 3: Can customers witness the hydraulic cylinder production and inspection process on site?
Yes. Customers can arrange technical personnel to witness key process inspections on site, verify inspection records and equipment calibration certificates. The factory opens the production site and cooperates with customers to complete quality acceptance.