Assembly process and quality control of protruding screw for external circulation catheterization
Release time:
2026-11-11
In a protruding-tube design the return tube is a separate, self-contained component rather than a part recessed into the nut body. That single fact moves the manufacturing emphasis: the nut no longer carries a spiral groove, but the tube itself must be formed to a far tighter three-dimensional tolerance, and every demand for accuracy is transferred from the nut to the tube and to the joint between them.
The payoff is real. Because the tube is made independently, its bend radius and internal finish can be optimised without regard to nut machining, which is why a protruding type generally recirculates more smoothly and quietly than an embedded one. The price is paid at assembly: alignment between the tube ports and the ball entry and exit holes is unforgiving, and a deviation that would have been absorbed by a machined groove instead becomes an impact load on every ball that passes through.
1. Forming the Protruding Return Tube
Because the tube is a standalone part, its forming precision sets the ceiling for recirculation quality. Compared with the embedded type it can be formed to a higher standard, but it places correspondingly stricter demands on assembly alignment.
The essential difference is one of tolerance ownership. In an embedded design the nut groove and the tube are matched to each other, so small deviations in either can partially cancel. In a protruding design the tube is located only at its two ports; everything between them is free-standing, so any deviation in the bend appears directly as a mismatch at the port.
2. Tube Manufacturing Operations
Tube selection and cutting. Thin-wall seamless precision steel tube is used, with wall thickness chosen against ball diameter and impact load. Cut length is calculated from the developed helix length with allowance at both ends for the port cuts.
CNC tube bending. This is the core operation. The tube must be bent into the precise three-dimensional curve that matches the screw helix, normally on a CNC bender with dedicated tooling. Too tight a bend radius wrinkles the inside wall, thins the outside wall and can crack the tube outright — a defect that is invisible from the outside and fatal in service.
End cutting. Both ends are cut at the angle of the ball entry and exit holes so that the tube meets the nut ports without a step. Edges are then deburred and rounded; a sharp edge here is the single most common cause of ball damage at the transfer point.
Internal polishing. The bore is polished to a low roughness to reduce friction and noise as balls pass through, then inspected by borescope to confirm that no scoring remains.
3. Assembling the Tube to the Nut
Ball entry and exit holes. The holes in the nut are machined to the angle of the tube ports, with rounded edges to protect the balls.
Tube positioning. The tube ports are offered up to the holes and held with a dedicated fixture. Alignment tolerance is extremely tight: a misalignment of as little as 0.1 mm is enough to make every ball strike the port edge as it transfers, producing impact wear that shows up quickly as noise and then as spalling.
Fixation. Two families are used. Removable fixation uses a clamp or a threaded gland, so the tube can be replaced without scrapping the nut. Welded fixation applies local welds for higher strength, at the cost of being non-removable. The choice is a serviceability decision as much as a strength one.
Sealing. Sealant or an O-ring is applied at the tube-to-nut joint to prevent grease loss, which is the failure most likely to follow a removable tube in a dusty environment.
4. Quality Control Points
Each operation has a defined check, and the checks are ordered so that an expensive tube is not scrapped by a fault that could have been caught one stage earlier.
Operation | Inspection item | Method |
Tube bending | Bend angle, radius of curvature, twist | Dedicated gauge, optical projector |
End cutting | Cut angle, burr | Optical projector, roughness tester |
Tube bore | Roughness, scoring | Borescope |
Assembly alignment | Coaxiality, step at joint | Ball-pass test, plug gauge |
Fixation strength | Tensile and torsional resistance | Tensile / torque test |
Circulation test | Smoothness, noise | Running test rig |
5. Factory Inspection and Typical Defect Countermeasures
Beyond the standard accuracy items, a protruding-tube screw needs three tests aimed at the tube itself: a vibration test to prove the fixation cannot work loose, a full-stroke noise test to expose port mismatch, and a sealing check at the tube joints. Where the tube is removable, repeatability of positioning after removal and refitting must also be verified, because the customer will rely on that property.
The recurring problems and their standard countermeasures are set out below. Each one has a root cause in the process rather than in the operator, which is why each is answered by a change to method or tooling.
Item | Typical problem | Countermeasure |
Tube bending | Wrinkling on the inside of the bend | Increase bend radius or reduce the angle bent in a single pass |
Port alignment | Deviation between tube port and ball holes | CNC positioning fixture referenced from the ball entry and exit holes |
Fixation | Tube works loose in service | Use welded fixation or a heavy-duty clamp matched to the load spectrum |
Tube bore | Scoring from a missed polishing step | Make bore inspection a mandatory, sign-off process step |
6. Quality Assurance System
Incoming inspection. All raw materials — steel, balls, seals, grease — are checked for composition, mechanical properties and dimensional accuracy before they enter stores. Non-conforming material is not booked in.
In-process inspection. A check point follows every critical operation, covering dimensions, hardness and surface condition.
First-article inspection. The first piece of each batch is inspected and approved before series production begins; it is the first line of defence against a batch-wide fault.
Patrol and sample inspection. Periodic checks during production monitor process stability and batch consistency.
Final inspection. Every screw is fully inspected before dispatch, covering accuracy, preload and running performance.
7. Inspection Equipment and Capability
A competent manufacturer needs equipment matched to the tolerance being claimed. The capability table below is the minimum set for a protruding-tube product, where bore condition and joint alignment matter as much as thread accuracy.
Inspection item | Principal equipment | Capability level |
Thread accuracy | Universal toolmaker's microscope, laser interferometer | Micrometre |
Profile and roughness | Contour recorder, roughness tester | Nanometre |
Material properties | Hardness tester, spectrometer | Comprehensive |
Geometric accuracy | Roundness tester, CMM | Micrometre |
Running performance | Ball screw test rig | Full parameter set |
8. Process Documentation and Traceability
Every screw should ship with a complete record: raw material batch and test certificate; machining parameters for each operation; heat treatment curves and results; thread grinding parameters; assembly and preload records; final inspection report. Together these form the traceability chain, so that a fault found years later can be followed back to a specific tube batch, fixture or shift.
9. Non-Standard Capability
For unusual duties the manufacturer should be able to vary: special diameter and lead combinations; left- and right-hand threads; special accuracy grades; special materials and surface treatments; special structures and functions such as self-limiting or multi-stage designs; special protection and sealing arrangements. Non-standard work needs the technical requirements, acceptance criteria and delivery terms agreed in writing before production starts.
10. Packaging and Delivery
Threads and raceways are treated against rust; the nut is fitted with a protective sleeve so that balls cannot fall out and debris cannot enter; shock- and moisture-absorbing materials are used for packing; long-distance shipments are secured in a wooden crate; and the consignment is accompanied by the full technical file and inspection report. The protruding tube needs specific attention here: it is the most exposed part of the assembly and should be individually padded so that it cannot be bent in transit.
Frequently Asked Questions
Why can a protruding tube be formed more accurately than an embedded one?
Because it is made as a free-standing part rather than being forced to match a groove cut in the nut. Its bend radius and bore finish can be optimised on their own terms, which is why a protruding design normally runs more smoothly and quietly.
How closely must the tube ports meet the ball holes?
Within roughly a tenth of a millimetre. Beyond that, each ball strikes the port edge on every pass, and what begins as extra noise becomes spalling of the raceway. Dedicated fixtures referenced from the ball holes are the normal way to hold this.
Should the tube be clamped or welded?
Clamp or gland it where you expect to replace the tube during the life of the machine; weld it where impact loads are high and removal is not planned. A removable tube adds a sealing requirement at the joint, so grease loss must be checked at every service interval.