Common troubleshooting and daily maintenance of internal circulation ball screw pairs
Release time:
2026-11-04
1. Common Fault Symptoms and Root Cause Analysis
The great majority of faults encountered in internal-return ball screw assemblies trace back to one of three root factors: inadequate lubrication, failed contamination control, or a change in preload. Worn balls, scoring of the raceway and loss of positioning accuracy are usually the end result of one of these three rather than an independent defect. Learning to recognise the distinction makes fault diagnosis markedly faster and can cut machine downtime substantially.
A useful diagnostic habit is to record the operating context before dismantling anything: load, speed, duty cycle, ambient conditions, and how long the symptom has been present. A screw that has gradually lost accuracy over eighteen months points to progressive wear; a screw that began overheating within a week of recommissioning points instead to incorrect preload, misalignment or a lubrication delivery problem.
2. Troubleshooting Reference Table
The table below is intended for on-site use. Work from the symptom column to a likely cause, confirm it with the recommended check, and only then apply the corrective action. Jumping straight to disassembly is the most common cause of unnecessarily long stoppages.
Symptom | Likely cause | Diagnostic check | Corrective action |
Loss of transmission accuracy, positioning out of tolerance | Ball wear, preload decay | Measure axial clearance and preload | Adjust preload shim, replace balls |
Rising running noise, abnormal sound | Poor lubrication, ingress of foreign matter, damaged ball | Sound localisation, strip and inspect | Clean and re-lubricate, replace damaged parts |
Increased starting torque, stiffness or binding | Grease dried out, raceway corrosion, ball jammed in deflector | Turn by hand, check lubrication | Clean and lubricate, dress the raceway |
Excessive axial clearance, lost motion on reversal | Insufficient preload, worn shim | Measure clearance value | Fit a thicker shim and re-apply preload |
Abnormal heating at the nut | Preload too high, inadequate lubrication, poor alignment | Measure temperature, check mounting | Reduce preload, improve lubrication |
Balls falling out, nut seized | Deflector loose, protection failed | Strip and inspect the nut | Replace deflector, reload balls |
3. Routine Maintenance Specification
Preventive maintenance is far cheaper than corrective work. The four areas below, attended to consistently, account for the overwhelming majority of avoidable failures.
3.1 Lubrication management
Lubrication is the single most important factor in service life. Select the grease for the operating environment: lithium-based grease suits general-purpose use at normal temperatures, while high temperature or high speed duty calls for a synthetic grease. Inspect and replenish after the first 500 hours of operation, then every 2,000 to 4,000 hours thereafter, shortening the interval in harsh environments. A blocked lubrication line is the single most common trigger of fault conditions, so verify actual grease delivery rather than assuming the system is functioning.
3.2 Contamination control
Once hard particles such as swarf or grit enter the ball recirculation path of an internal-return screw they score the raceway rapidly and set up abrasive wear that no amount of subsequent lubrication can reverse. Covers and wiper seals must be kept intact, and in dusty environments a telescopic protective cover should be fitted as a matter of course.
3.3 Periodic preload inspection
On double-nut shim-preloaded types such as the GD design, preload decays over time as the balls wear. Check the starting torque every six months with a torque wrench; a marked drop means the shim thickness should be increased to restore preload. As a rule of thumb, preload is set at approximately 10% of the basic dynamic load rating Ca — high enough to eliminate lost motion, low enough to avoid unnecessary heat generation.
3.4 Temperature monitoring
Under normal operation the temperature rise should stay within a reasonable band, typically 20 to 30 °C above ambient. On detecting an abnormal rise, check lubrication and preload first, then examine mounting alignment. Thermal expansion is not a trivial consideration: a temperature change of just 2 to 4 °C is enough to produce a measurable change in travel, so high-speed precision applications should apply thermal compensation and allow a proper warm-up period.
4. Criteria for Repair versus Replacement
Return the assembly to the manufacturer for repair, or replace it outright, where any of the following is present: visible spalling or pitting on the raceway; a screw bent beyond the limit at which it can be straightened; a damaged nut deflector that prevents smooth recirculation; or axial clearance still out of tolerance after shim adjustment has reached its limit. Never attempt to regrind or lap a thread raceway in-house — this is work for the manufacturer alone, and an incorrectly dressed raceway will destroy the replacement balls within weeks.
5. Spare Parts Recommendations
Keep a stock of wear items alongside the equipment: balls of the matching size and diameter grade, wiper seals, protective boots and a range of preload shims. For critical plant, hold one complete nut assembly so that a failed unit can be swapped out and production resumed without waiting for a repair cycle.
6. Establishing a Structured Maintenance Management System
For any installation running ball screw assemblies, a formal maintenance regime will extend screw life significantly and reduce unplanned stoppages. The framework has five elements.
6.1 Maintenance procedure documentation
Set out an explicit maintenance schedule specifying the cycle, content, method and responsible party for every item. Ambiguity about who does what, and how often, is the fastest route to a regime that quietly lapses.
6.2 Maintenance records
Keep a log recording the date, scope, findings and outcome of every intervention. Over time this becomes a health record for the asset and gives genuine trend data rather than anecdote.
6.3 Spare parts inventory
Stock critical items according to the importance of the equipment: balls, seals, grease and preload shims as a minimum, and a complete screw assembly where the consequence of failure is severe.
6.4 Personnel training
Maintenance staff should be trained in the construction principle of the assembly, correct strip and rebuild procedure, and basic fault recognition. Ball screw assemblies are unforgiving of well-intentioned but uninstructed intervention.
6.5 Manufacturer support
Maintain a long-term relationship with the manufacturer and make use of their inspection equipment and engineering support for periodic in-depth health assessment. This is where the value of a supplier relationship beyond the initial order becomes apparent.
7. Early Warning Signs of Impending Failure
Most failures announce themselves well before they become critical. Catching these signals is largely a matter of paying attention during normal operation rather than running formal tests.
A change in sound — rising noise, a new abnormal tone, or a rhythmic periodic knock — often signals ball wear, raceway damage or an intruding particle. A rise in temperature points to insufficient lubrication, excessive preload or an alignment error. Increasing vibration may indicate a damaged ball, raceway spalling or a failing support bearing. Falling positioning accuracy, with growing lost motion on reversal, usually means preload decay or raceway wear. Rising running or starting torque suggests dried grease, corrosion in the raceway or a blocked recirculation path. Finally, visual cues — grease leaking from the nut, a torn cover, or swarf collecting around the nut — all call for immediate attention rather than a note in next week's maintenance plan.
8. General Principles for Handling Faults
Four principles keep a fault from turning into a write-off.
- Stop first, inspect second. Shut the machine down as soon as an anomaly is detected; running on in a degraded state converts a modest repair into a major one.
- Work from simple to complex. Check lubrication, sealing and external condition before preload and accuracy, and strip the assembly only as a last resort.
- Record the data. Log temperature rise, vibration, torque and accuracy readings throughout the investigation so that severity and trend can be judged rather than guessed.
- Escalate what needs expertise. Anything involving internal strip-down or accuracy restoration should go to the manufacturer or a qualified specialist; do not grind, modify or re-assemble critical internal parts on site.
9. Key Measures for Extending Service Life
Service life is determined less by the specification on the drawing than by use.
- Operate within the rated load and speed, and avoid overload, overspeed and overtravel.
- Lubricate properly, on schedule, and keep the grease lines clear of obstruction — this is the single most effective life-extension measure available.
- Protect the assembly: intact covers and seals keep particulate matter out of the recirculation path.
- Inspect periodically — preload, accuracy, temperature rise and vibration are the four indicators worth tracking.
- Control the environment, or specify for it. In dusty, corrosive or high-temperature duty, either strengthen the protection or choose a purpose-designed variant such as a salt-spray-resistant screw.
10. Working with the Manufacturer
A long-term collaborative arrangement with the manufacturer improves equipment reliability well beyond what either party achieves alone. Arrange periodic technical visits; use the manufacturer's inspection equipment for deep assessment; set up a rapid-response channel so that support is available when a failure does occur; and keep abreast of the manufacturer's product development so that retrofit opportunities are not missed when a machine is next overhauled.
Frequently Asked Questions
How often should an internal-return ball screw be re-lubricated?
Inspect and replenish after the first 500 hours of operation, then every 2,000 to 4,000 hours thereafter. Shorten the interval in dusty, humid or high-temperature environments, and always confirm that grease is actually reaching the raceway — a blocked line is the most common cause of premature failure and is invisible from outside.
What does an abnormal temperature rise at the nut usually indicate?
Under normal conditions the rise is 20 to 30 °C above ambient. A larger rise most often means excessive preload, insufficient lubrication or poor mounting alignment, in that order of probability. Shut down and check those three items before considering anything more exotic; note that even a 2 to 4 °C change alters travel measurably, so warm-up matters on precision axes.
When should a ball screw be sent back rather than repaired on site?
Send it back where there is visible spalling or pitting on the raceway, a bend beyond what can be straightened, a damaged deflector, or axial clearance still out of tolerance after shim adjustment has been exhausted. Never attempt to regrind or lap a thread raceway in-house — an incorrectly dressed raceway will destroy the replacement balls within weeks.