Manufacturing process and quality control points of internal circulation ball screw pair
Release time:
2026-11-03
1. The Complete Manufacturing Flow: From Raw Material to Finished Assembly
Manufacturing an internal-return ball screw assembly is a multi-stage precision machining process. Any deviation in an earlier operation is amplified by subsequent stages and ultimately manifests as errors in transmission accuracy and service life. Understanding this chain is essential for both procurement engineers specifying a supplier and quality teams auditing one.
The process begins with material selection and billet preparation, proceeds through thread-race generation, heat treatment, finish grinding, nut machining and deflector assembly, ball matching and preload adjustment, then moves into final inspection, rust prevention, protective packaging, and delivery. Each stage has its own critical-to-quality characteristics, and each must be controlled independently before the next can begin.
2. Core Manufacturing Operations
2.1 Screw blank preparation and rough machining
The process starts with the selection of high-quality alloy steel. The billet is cut to length, both end faces are faced, centre holes are drilled, and the outer diameter and thread root diameter are rough-turned with finishing stock deliberately reserved. The centre holes serve as the datum for the entire screw machining sequence and must be produced to high precision and kept clean throughout; damage or contamination at this stage propagates as roundness and run-out errors later.
2.2 Thread raceway machining
This is the most critical operation in the entire process. High-precision screws are produced by thread grinding on dedicated thread-grinding machines, using formed grinding wheels to generate the exact helical raceway geometry. Grinding parameters must be set strictly according to the pitch and the material being machined. For medium- and lower-precision screws, processes such as whirlwind milling or thread rolling may be used instead, offering substantially higher productivity.
2.3 Heat treatment
The threaded portion of the screw must be induction-hardened (medium-frequency) or through-hardened. Both the depth of the hardened layer and the distribution of hardness directly affect wear resistance and contact fatigue life. After hardening, the screw must be straightened; excessive deviation in straightness will cause jamming or uneven running in service.
2.4 Finish grinding of the outer diameter and thread
Following heat treatment, the outer diameter and the thread are finish-ground. The finished thread must meet the dimensional and geometric requirements of the specified accuracy grade. For internal-return screws in particular, the cross-sectional shape of the thread raceway and its surface roughness have an especially large influence on the smoothness of ball recirculation.
2.5 Nut machining and deflector assembly
The internal thread of the nut is finish-ground in the same way. The deflector pockets must be positioned precisely relative to the thread raceway. With internal-return fixed deflectors, the balls must be able to reverse smoothly through the return path; the assembly clearance between the deflector and the nut must be tightly controlled.
2.6 Ball matching and assembly
The balls are size-graded and matched so that the diameter variation across all circuits stays within an extremely narrow band. During assembly, preload must be controlled for double-nut, shim-preloaded types such as the GD design, while axial clearance is controlled for single-nut types such as the G design.
3. Critical Control Points in Quality Management
The following table summarises the key characteristics monitored at each stage, together with the methods used to verify them. These are the items a buyer should ask a supplier to demonstrate during an audit.
Operation | Key dimension or parameter | Inspection method |
Thread grinding | Pitch error, half-angle of thread flank | Universal toolmaker's microscope, thread gauges |
Heat treatment | Surface hardness, case depth | Rockwell hardness tester, metallographic microscope |
OD finish grinding | Roundness, cylindricity, straightness | Roundness tester, contour measuring instrument |
Deflector assembly | Positional accuracy, smoothness of recirculation | Ball pass test, running feel check |
Finished assembly | Travel deviation, axial clearance, preload | Screw performance test bench |
4. Finished-Product Acceptance Tests
Finished assemblies are accepted in accordance with GB/T 17587.3. The inspection covers the travel compensation value c within the effective travel, the target-travel tolerance ep, the travel variation Vup for positioning (P-class) assemblies, the travel variation V300p over any 300 mm of travel, and the travel variation V2πp over one 2π-radian rotation. In addition, axial clearance, preload, starting torque, and smoothness of running are all verified.
5. Packaging and Protection
Ball screws are precision transmission components and require careful protection before dispatch. A rust-preventive treatment is applied — either rust-proof oil or volatile corrosion inhibitor paper — and a protective sleeve is fitted over the nut to prevent ball loss and the ingress of foreign matter. Packaging uses shock-absorbing, moisture-resistant materials, and long-distance shipments are additionally crated and braced with a wooden frame.
6. The Quality Assurance System Behind the Manufacturing Process
As a precision transmission component, the quality of a ball screw assembly is determined by the level of control exercised across the entire manufacturing process. A robust quality assurance system should contain the following elements.
6.1 Incoming material inspection
All incoming raw materials — steel, balls, seals, lubricating grease and so on — are inspected before they may enter stock. Checks cover material composition, mechanical properties and dimensional accuracy; any non-conforming material is rejected and must not be accepted into inventory.
6.2 In-process inspection
An inspection point is established after every key operation, covering dimensional checks, hardness testing and surface-quality evaluation, so that process quality remains controllable at each step.
6.3 First-article inspection
Before each production batch, a first article is produced and inspected. Full-scale production may only begin once it has passed. First-article inspection is the first line of defence against batch-scale quality problems.
6.4 Patrol inspection and sampling
During production, regular patrol inspections and finished-product sampling are carried out to monitor process stability and batch-to-batch consistency.
6.5 Finished-product inspection
Every screw is subject to a complete finished-product inspection before dispatch, covering accuracy, preload and running performance.
7. Inspection Equipment and Capability
A professional ball-screw manufacturer should possess a full range of inspection equipment and the corresponding measurement capability. The table below gives an overview of the equipment typically required and the precision levels involved.
Inspection item | Main equipment | Precision level |
Thread accuracy | Universal toolmaker's microscope, laser interferometer | Micrometre-level |
Contour and roughness | Contour measuring instrument, roughness tester | Nanometre-level |
Material properties | Hardness tester, spectrometer | Comprehensive |
Geometric accuracy | Roundness tester, coordinate measuring machine | Micrometre-level |
Running performance | Screw performance test bench | Full-parameter |
8. Process Documentation and Traceability
Every screw should be accompanied by complete process documentation and inspection records, including: the raw-material batch number and its inspection report; the machining parameters recorded for each operation; the heat-treatment curve and its test results; the thread-grinding parameters; the assembly and preload records; and the dispatch inspection report. Together, these records form the product's quality traceability system and make it possible to locate the cause quickly should a problem arise.
9. Non-Standard Customisation Capability
For demanding or unusual operating conditions, a manufacturer should offer non-standard customisation covering: special diameter and lead combinations; special thread directions (left-hand or right-hand); special accuracy grades; special materials and surface treatments; special structures and functions (such as self-limiting and multi-stage designs); and special protection and sealing requirements. Non-standard work requires thorough communication with the manufacturer in advance to establish the technical requirements, acceptance criteria and delivery schedule.
10. Packaging and Delivery
For precision screws, packaging has a direct bearing on transport safety. The thread and raceway surfaces receive rust-preventive treatment; the nut is fitted with a protective sleeve to prevent ball loss; shock-absorbing, moisture-resistant materials are used; long-distance shipments are crated with a wooden frame for additional bracing; and complete technical documentation and inspection reports are enclosed.
Frequently Asked Questions
What is the most critical operation in manufacturing an internal-return ball screw?
Thread raceway machining. For high-precision screws this is done by thread grinding on a dedicated machine using a formed grinding wheel. The cross-sectional shape and surface roughness of the raceway directly determine how smoothly the balls recirculate, while pitch accuracy and flank geometry govern positioning performance. Errors introduced here cannot be corrected by later operations.
How is product quality verified before a ball screw leaves the factory?
Every assembly is tested against GB/T 17587.3. The inspection covers travel compensation within the effective travel, target-travel tolerance, travel variation for positioning-class assemblies, travel variation over any 300 mm, travel variation over one 2π-radian rotation, and axial clearance, preload, starting torque and running smoothness. In addition, the manufacturer's quality assurance system includes incoming, in-process, first-article, patrol and finished-product inspection stages.
Can ball screw assemblies be supplied for non-standard applications?
Yes. Non-standard customisation can cover special diameter and lead combinations, left- or right-hand threads, special accuracy grades, special materials and surface treatments, special structures such as self-limiting and multi-stage designs, and special protection or sealing requirements. It does, however, require detailed technical discussion in advance to define the requirements, acceptance criteria and delivery schedule.