Energy mining equipment oil cylinder | on sale | factory inspection
Release time:
2026-07-14
How to conduct final inspection on piston rod surface quality before delivery?
Inspection Standards and Procedures
A full-range rigorous final inspection is implemented for the outer surface of piston rods to ensure surface flatness, uniformity and wear resistance of protective coatings.
Full visual inspection: Under strong lighting conditions, a 360° visual inspection is performed on the outer circle of the piston rod. No visible pinholes, peeling, burrs or mechanical bruises are allowed. The coating or cladding surface must have uniform color without scorching or local darkening defects.
Roughness and hardness sampling inspection: Batch sampling is carried out to test surface roughness and hardness. The surface roughness Ra is required to be ≤0.4μm. The surface hardness of hard chrome plating reaches HV≥800, while the hardness of laser cladding layers complies with corresponding process standards to ensure qualified wear resistance.
Coating thickness verification: A magnetic thickness gauge is used for multi-point thickness measurement of hard chrome plating layers. For laser cladding layers, metallographic section inspection reports are verified to ensure the minimum thickness meets drawing design requirements.
Judgment criteria: Any product with penetrating scratches or coating peeling on the surface is judged unqualified and prohibited from warehousing and delivery.
What are the mandatory hydrostatic test standards for hydraulic cylinders before delivery?
Test Implementation Procedures
All hydraulic cylinders must undergo a standard static pressure test before leaving the factory to verify overall structural tightness and pressure resistance.
Test preparation: Exhaust air inside the hydraulic cylinder, close the oil inlet and outlet ports, and keep the piston rod in a fully extended state.
Pressurization and pressure holding: Gradually increase the pressure to 1.5 times the rated working pressure (in accordance with GB/T 15623 standards and contract agreements). The pressure holding time shall not be less than 5 minutes; high-pressure hydraulic cylinders usually extend the holding time to 10-30 minutes.
Leakage inspection: Observe all welding joints, static sealing surfaces and piston rod surfaces of the cylinder for external leakage. Meanwhile, check the cylinder barrel for permanent deformation or abnormal expansion.
Judgment criteria: Products are qualified if there is no obvious pressure drop during pressure holding, no external leakage and no plastic deformation of the cylinder structure.
How to verify the cleanliness of cylinder inner bores during factory inspection?
Inspection Methods and Criteria
Multiple detection methods are adopted to strictly control the internal cleanliness of multi-stage cylinder barrels and eliminate residual impurities.
Endoscope inspection: An industrial endoscope is inserted into the interior of multi-stage cylinder barrels to inspect the inner wall laser cladding or plating surface, ensuring no residual foreign matters such as iron filings, welding slags and metal powder.
Flushing sampling method: For hydraulic cylinders with high-precision requirements, circulating flushing is performed after assembly. Oil samples are collected for particle count analysis to meet the cleanliness level specified in the contract.
Visual confirmation: In the absence of an endoscope, high-intensity flashlight transmission inspection is adopted to confirm no sludge or impurities accumulate at the cylinder bottom and dead corners.
Judgment criteria: Products can proceed to the next process only when no hard particles are found in the endoscope field of view and the oil sample test results meet the standards.
How to inspect the internal quality of welds via non-destructive testing before delivery?
Inspection Specifications and Grading Standards
Standardized non-destructive testing (NDT) is implemented for cylinder welds to eliminate internal and surface hidden defects.
Testing proportion: 100% full non-destructive testing is mandatory for key load-bearing welds, including cylinder bottom welds and lug welds. Secondary welds are sampled and inspected in accordance with GB/T 7939 and relevant industry standards.
Testing methods: Ultrasonic testing (UT) is mainly used to detect internal defects such as pores, inclusions and incomplete fusion. Magnetic particle testing (MT) is supplemented for surface areas such as cylinder mouths to identify tiny surface cracks.
Grading criteria: Referring to GB/T 11345 standard, the weld quality grade must reach Grade II or above. Hazardous defects including cracks and incomplete penetration are strictly prohibited.
Judgment criteria: All test reports are filed for traceability. Welds with unqualified defects must be repaired and re-tested until fully qualified.
Key evaluation indicators of the full-stroke operation test
On-site Inspection Content and Rules
The full-stroke reciprocating operation test comprehensively verifies the operational stability, coordination and buffering performance of hydraulic cylinders.
Low-speed crawling test: Under no-load or low-pressure conditions, adjust the flow rate to make the piston rod extend and retract at an extremely low speed (≤50mm/min). The operation must be stable without crawling (intermittent jumping movement).
Reversing impact inspection: During full-stroke reciprocating operation, check for abnormal mechanical impact sounds at the moment of reversing and verify qualified buffering performance.
Speed synchronization test (multi-stage cylinders): For multi-stage hydraulic cylinders, confirm the extension and retraction sequence of each stage strictly conforms to the design logic, with no jamming or structural interference.
Judgment criteria: Products are qualified with stable operation, no crawling, no abnormal noise and coordinated movement of all cylinder stages.
What inspection certification documents are delivered with finished hydraulic cylinders?
Complete Delivery Document List
All factory-qualified hydraulic cylinders are delivered with complete, traceable official inspection documents.
Factory test report: Includes hydrostatic pressure test curves and records, full-stroke operation test records, minimum starting pressure values and leakage detection results, stamped with the official "Inspection Qualified Seal".
Material and process certification documents: Material quality certificates for core raw materials (cylinder barrel, piston rod); process execution records and test reports (thickness, hardness) for key procedures such as laser cladding and heat treatment.
Non-destructive testing report: Original or copied UT/MT inspection reports for key load-bearing welds.
Product certificate and nameplate: Official product certificate (including unique serial number and manufacturing date). The nameplate information is completely consistent with the certificate to support full life cycle quality traceability.
Judgment criteria: Products without complete documents, inconsistent data or unapproved inspector signatures are prohibited from factory delivery.
FAQ 1: What core items are included in piston rod surface final inspection?
The final inspection covers full visual appearance check, sampling test of surface roughness (Ra≤0.4μm) and hardness, as well as coating thickness verification. Products with penetrating scratches or coating peeling are unqualified.
FAQ 2: What is the standard hydrostatic test pressure and holding time for mining hydraulic cylinders?
The test pressure is 1.5 times the rated working pressure. The minimum holding time is 5 minutes, and 10-30 minutes for high-pressure cylinders. Products are qualified with no pressure drop, leakage or plastic deformation.
FAQ 3: What official inspection documents are provided with cylinder delivery?
The delivery package includes factory test reports, raw material and process certification documents, weld non-destructive testing reports, and product qualification certificates with matched nameplate serial numbers for full lifecycle traceability.